Posts Tagged ‘K&N’

New K&N Intake for FJ Cruiser/4Runner

September 15th, 2010 Comments off

The K&N 77-9034KP intake system is designed to replace the factory air filter, air box, and air intake tube with components which are less restrictive, so that the vehicle’s engine performs up to its full potential. Installation of the 77-9034KP is easy, and begins with the removal of the stock intake pieces. In their place go a brightly finished, mandrel-bent aluminum tube, and a large cone shaped air filter that can withstand the abuse of dust and dirt on any trail these vehicles might venture down.

These components have been designed by K&N engineers to be much less restrictive to air flow than their factory counterparts. With K&N’s intake these engines will not waste power trying to pull in the air they need. In addition to being less restrictive, the K&N air filter included in this system (part number RF-1044XD) is protected by a powdercoated steel heat shield, which helps keep intake air temperatures down where they belong. A K&N test on this filter design resulted in showing it has excellent filtration at 99.01% overall efficiency (ISO 5011 test results). According to testing performed on K&N’s dynamometer, the air intake system pushes out an impressive additional 13.55 horsepower and 14.55 lb. ft. torque at 5000 RPM on a 2010 Toyota FJ Cruiser. The 77-9034KP is backed by K&N’s Million Mile Limited Warranty.

Click here for the dyno sheet

New K&N Intake for 3.6L V6 Camaro

April 6th, 2010 Comments off

The 2010 Chevrolet Camaro 3.6L V6 has great looks, quality interior, and a fair amount of performance. However for added performance, K&N designed an air intake system that boosts horsepower while protecting your engine from elements that could damage your engine. The 2010 Camaro will really scream after this simple modification. The 63-3075 was dyno tested and shown to increase the 2010 Chevy Camaro 3.6L V6 by just under 15 horsepower at 6200 RPM.

The K&N air intake replaces the restrictive factory air filter and intake housing with a custom intake tube and K&N high-flow air filter. (By smoothing and straightening air-flow to your engine and allowing air to flow easier into your engine, more horsepower is achieved) K&N air intakes use a washable and reusable air filter and are backed by a Million Mile Limited Warranty.

K&N Releases New 2010 Camaro Intake Kit

January 21st, 2010 Comments off

K&N’s 63 Series AirCharger Intake Kits are guaranteed to increase horsepower and come with a Million Mile Limited Warranty. K&N intake systems replace your vehicle’s restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction as they smooth and straighten air flow. This allows your vehicle’s engine to inhale a larger amount of air than the OEM air filter assembly. More air means more usable power and acceleration throughout the engine’s RPM range. The filters on these kits are washable and reusable.

Click here for more info.

K&N Releases New Intake For 2010 Camaro

December 17th, 2009 Comments off

K&N’s Research and Development Department tested the New K&N Typhoo Intake on a 2010 Chevrolet Camaro SS with a 6.2 liter V8 engine on one of their in house dynamometers. Results showed an increase across the RPM range with a peak horsepower gain of 18.12 horsepower at 5200 RPM.

In addition to power gains, K&N air intake systems are also designed to increase filtering capacity and improve throttle response. The heat shields are engineered to isolate the oversized K&N chrome top high flow air filter from engine bay heat.

This air intake kit also makes use of the Camaro’s factory fresh air duct which provides cooler outside air to the K&N air filter. This filter captures harmful particles, increases airflow and also increases service life. It will perform for up to 100,000 miles before service is required depending on driving conditions.

The mass air sensor is installed in the 90 degree bright intake tube. The mass air sensor adaptors are precision CNC machined, 6061 billet aluminum for accurate mass air flow sensor readings.

It takes about 90 minutes to install. This K&N air intake system, like all other K&N air intake systems is backed by the famous K&N Million Mile Limited Warranty.